Arlo Doorbell Flashing Red and White (Quick Fixed)
A vital component of a home security system, Arlo Doorbells notify you of all activity on the door side.
Arlo also flashes LED lights, such as the Red and White LED on the doorbell, so you might be wondering why my Arlo doorbell flashes red and white.
When your Arlo doorbell starts flashing red and white, it means that it isn’t getting enough power, is looking for power, or is trying to connect to Wi-Fi.
Let me tell you more about my research that I did on the flashing red and white lights of Arlo doorbell, and tell you some potential fixes to it.
Let’s get started!
Why Is My Arlo Doorbell Flashing Red and White?
Sometimes a dead or low battery and poor wiring might prevent your Arlo doorbell from receiving adequate power.
Make sure the battery of the Arlo doorbell is completely charged and check to see if there are any loose electrical connections before trying to fix the doorbell and switch on the flashing lights.
Additionally, there is a chance that the doorbell is attempting to connect itself to a Wi-Fi connection but is having trouble doing so because of a poor signal or also an invalid password for Wi-Fi.
How You Can Fix the Arlo Doorbell Flashing Red and White?
As we discussed the common causes:
- Arlo doorbell has a Low Battery
- It is facing power issues
- The Arlo doorbell needs a reset
- There is a problem with the Wi-Fi connection
Now, let me resolve these issues for you so that you can easily use your Arlo doorbell in the future.
Arlo doorbell has a low battery
Sometimes the Arlo doorbell displays a blinking red LED because it is not receiving enough energy or because the battery or Arlo doorbell is very close to dying.
The flashing LED serves as a warning that the battery needs to be recharged or changed.
Solution:
- The battery has to be charged or changed!
- Remove the doorbell’s battery!
- Recharge the battery!
- Use a USB cable to attach it to a power source!
- If not, you must swap out your battery!
It is facing power issues
The major cause of this problem is because not enough electricity is being received to operate.
One possible cause of this might be the transformer is not supplying enough power since the doorbell is not tightly linked to it.
Also when there is a power surge, doorbells might become trapped in the flashing mode.
Solution:
- To fix this issue, you should examine your power source!
- To make sure that the transformer is supplying the right voltage, you should inspect the doorbell’s connection. Replace it in case it is producing low voltages at the prescribed voltage!
- To fix the issue of a power surge, try reconnecting the doorbell after totally removing it from the power supply, Wi-Fi, and phone!
Problem with the Wi-Fi network
Your Arlo doorbell might not be able to upload or record a video to the storage of the cloud when you have a bad Wi-Fi connection, which is why it displays a red and white LED to signal possible problems.
Solution:
- Check the strength of the Wi-Fi first!
- To boost the signal, place the doorbell nearer to the router or install a Wi-Fi extension!
- To check if it helps, you may also try to reset your doorbell and wifi!
The Arlo doorbell needs a reset
Your doorbell’s software may have problems that prohibit it from connecting itself to the Internet or the app.
In this case, doing a factory reset will be a potential solution. This procedure resets the gadget to its factory default settings and refreshes it.
Your doorbell won’t have any issues after being reset, and you can get it back to running.
Solution:
Here is how you can perform the factory reset:
- To avoid any problems, delete the Arlo doorbell from your phone or Arlo account!
- Find the release pin as it was included with your Arlo doorbell device, or use something similar!
- For 15 seconds, press and then hold the reset button on the doorbell’s rear!
- When the reset procedure has been properly started by the doorbell, a white light will blink on the doorbell button!
- Add the Arlo doorbell to your account when the reset is finished if you want to use it again!
There is some technical issue
There can be possibilities that the Arlo doorbell is facing some kind of technical or complicated issue that only professionals can solve.
Solution:
- In this situation, all you need to do is to contact the customer support team of the Arlo doorbell!
- A team of professionals will be available to help you out!
You can watch this video as well.
Frequently Asked Questions
Is the Arlo doorbell functional without being linked to the Arlo app?
No, using the doorbell of Arlo without having it connected to your Arlo app is not possible. To configure and manage your Arlo doorbell, including getting alerts when motion or a doorbell ring is detected, you must use an app.
Is the Arlo Doorbell’s red and white configuration flashing normally?
No, flashing red and white on the Arlo Doorbell during setup is not usual. If you experience this difficulty, it was probably caused by a setup error. It is advised that you follow the troubleshooting instructions supplied by Arlo support or consult the product manual for guidance.
How can I connect the Arlo app to the Wi-Fi network?
Check to see whether the Arlo doorbell is in pairing mode by looking for red and white flashing lights. Then, to connect your doorbell to your Wi-Fi network, open the app of Arlo on your device, choose “Add the Device,” and then adhere to the instructions.
Conclusion
I hope now you know very well why is the Arlo doorbell flashing red and white light.
You can follow the above fixes to solve your issue like checking the battery, power source, Wi-Fi, or resetting the Arlo doorbell.
I hope you find this article helpful, and will surely apply the following fixes on your Arlo doorbell to solve your issue.
Related Posts
